The Jet series of pumps from DAB are Centrifugal self-priming pumps complete with ejector and diffuser for high priming capability. Suitable for drawing ground water from a well up to 9 meter deep, provided in 3 different material pump body: cast-iron, stainless steel and technopolymer.
Operating range: flow up to 80 l/min, head up to 62 m.
Self-priming: up to 9 meter.
Working pressure: 8 bar.
Max liquid temperature: 40°C.
These pumps were engineered perfectly for use in the Australian sand spear well installation. If your ground water is deeper than 9m and you require an above ground pump then an ejector valve can be paired to the appropriate DAB jet pump to increase the suction lift to 27m below ground!!! With this type of range, we are positive we can match a cost-effective pump to any sand spear or ground water well installation.
When choosing a pump, the phrase “horses for courses” never rang more true. It is vitally important that you match your pump to your flow conditions of your well and spear selection. If you go to big, you will end up drawing the well down too quickly and the pump will forever be cycling on and off causing premature pump failure. Too small and ou may not achieve the lift you need or the head pressure will be affected thereby forcing the pump to work too hard again, causing premature failure.
Choosing the correct pump will provide a long service life and fault free operation. If you have any questions regarding pump choice, please feel free to call or email and will assist with pump selection.
Jet Cast-Iron
Self priming centrifugal pump with excellent suction capacity even in the presence of air bubbles. Suitable for pumping water with low levels of sandy impurities. Especially used in domestic water supply installations. Suitable for small farms and gardening, small scale industrial services and where self priming is necessary.
TECHNICAL DATA
Operating range: from 0.4 to 10.5 m3 /h with head up to 62 metres. Liquid quality requirements: clean, free from solid or abrasive contaminants, non-viscous, non-aggressive, uncrystallised and chemically neutral, close to the properties of water. Liquid temperature range: for domestic use: from 0°C to +35°C (EN 60335-2-41) for other use: from 0°C to +40°C Maximum ambient temperature: +40°C Maximum operating pressure: 8 bar (800 kPa) Installation: fixed in a horizontal position. Special executions on request: different frequencies and/or voltage. Motor protection rating: IP 44 Terminal block protection rating: IP 55 Insulation class: F Standard input voltage: single phase 220/240 V / 50 Hz
Jetinox
Self priming centrifugal pump with excellent suction capacity even in the presence of air bubbles. Suitable for pumping water with low levels of sandy impurities. Especially used in domestic water supply installations. Suitable for small farms and gardening, small scale industrial services and where self priming is necessary
Operating range: from 0.4 to 10.5 m3/h with head up to 62 metres. Liquid quality requirements: clean, free from solid or abrasive contaminants,non-viscous, non-aggressive, uncrystallised and chemically neutral. Liquid temperature range: for domestic use: from 0°C to +35°C (EN 60335-2-41) for other use: from 0°C to +40°C
Maximum suction depth: 8 metres. Maximum ambient temperature: +50°C Maximum operating pressure: 8 bar (800 kPa) Installation: fixed in a horizontal position. Special executions on request: alternative voltages and/or frequencies. Motor protection rating: IP 44 Terminal block protection rating: IP 55 Insulation class: F Standard input voltage: single phase 220-240 V / 50 Hz
JetCom
This is the pump that will suit 98% of all sand spear installations. This pump is the most cost effective in the range and will provide years of faultless service. At $550 (ex gst/freight) this will out perform.
Self priming centrifugal pump with excellent suction capacity even in the presence of air bubbles. Suitable for pumping water with low levels of sandy impurities. Especially used in domestic water supply installations. Suitable for small farms and gardening, small scale industrial services and where self priming is necessary.
Operating range: from 0.6 to 5.4 m3/h with head up to 54 metres. Liquid quality requirements: clean, free from solid or abrasive contaminants, non-viscous, non-aggressive, uncrystallised and chemically neutral. Liquid temperature range: from 0°C to +35°C for domestic use (EN 60335-2-41). Maximum ambient temperature: +40°C Maximum operating pressure: 6 bar (600 kPa) Maximum suction depth: 8 metres. Installation: fixed in a horizontal position. Special executions on request: alternative voltages and/or frequencies. Motor protection rating: IP 44 Terminal block protection rating: IP 55 Insulation class: F Standard input voltage: single phase 220/240 V / 50 Hz